All Available Parts - 1967 Mercury Cougar

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Good used 'Control and Link Assembly - Door Latch Remote' as Ford calls these. This is the splined shaft assembly located just forward of the arm rest used to mount your interior door release handle for the right or passenger side door. These excellent used shafts are not only less money than the reproduction but the quality and fit is superior in all ways. We do not endorse the reproductions due to customer feedback being less than stellar. Comes with the retainer for the door latch rod as...

This is the assembly that your inside door handle attaches to and features all new components. They are gold cadmium plated to resist rust and corrosion. *NOTE* We have had complaints of these not fitting as well as originals, therefore we suggest buying our used units. Rod retainers not included. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored. Check out our video below for helpful tips on disassembling your vent and quarter windows:67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored.  Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Reproduction passenger side (right hand) vent window frame for the Mercury Cougar or Ford Mustang. This premium reproduction is a much better fit than the economy overseas version. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang.  This premium reproduction is a much better fit than the economy overseas version. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Used, with little to no scratches, suitable for every day driver.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

Fantastic quality in all respects, concours quality. Don't forget to select a mounting gasket and mounting kit if needed. Replaces Ford part # C7WY-17696-A.*NOTE* Mustang uses a different mirror and will not fit contrary to what you may have seen advertised elsewhere!Hole spacing: 4 3/8" Do you have riv-nut questions? Here are riv-nut answers! ...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Quality reproduction mirror for your 1967 - 1968 Cougar. Whereas it is not easily detected at first glance, the head of the mirror does have a slightly different contour than original. The base is spot on perfect and the controller, cable assembly are all excellent quality. The 67 style wand is no longer available, so this mirror includes the 68 style ball end wand. Plastic mounting pad and hardware included. *NOTE* Mustang mirrors will not work on a Cougar no matter what "they" told...

Finally! A correct looking and fitting quality mirror for the passenger side of your 1967 - 68 Cougar. This is NOT a Mustang part made to "kind of work". For years our customers have called almost weekly asking for the "RARE" 1967-68 right hand outside mirror listed in their owners manual as an option available at their local "Lincoln - Mercury Dealer". The intention may have been to offer one but it actually never came to be... This product has been getting great reviews in the Cougar...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

Reproduction convex passenger side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Reproduction driver side mirror lens replacement for the 67 - 68 Cougar chrome side mirror. NOTE: The narrow end of the mirror goes up top on Cougar and is reversed for Mustang. These mirrors are manufactured for the Mustang, so the small supplier part number at the bottom will be upside down and on top for Cougar. 

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

Used on all 1967 lower hinges and 1968 cast iron lower hinges. Perfect replacement for the spring that loads the door position detent plate against the position roller. Springs are painted for corrosion protection. Sold individually, two required per car. Replaces Ford Part #: C0DZ-6421232-B.

Early 68 cars often used this 2 1/2" pin as well. Sold individually, four required per car. Replaces Ford part #: B9A-5943030-AA.

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

Kit replaces one side. Contains all necessary parts including pins, bushings, a new cam plate, spring, and roller to rebuild both upper and lower hinges. This kit is for the cast iron type hinges found on the 1967 and early 1968 Cougar.Replaces Ford Part #: C5ZZ-6522800-K.

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

1967 Cougars used this cast iron hinge that weighs a pound or more over the 1968 stamped steel version. You may want to opt for a 1968 hinge if your goal is to lighten your car. You will shed about six pounds if you replace all four with a set of 1968 stamped steel Mercury Cougar door hinges. These used hinges usually need new pins and bushings, for the small cost of the new parts we suggest you purchase the Complete Hinge Rebuild Kit. Check out our hinge rebuild video below for more info. ...

[No Description Provided]

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

Used original door latch rod for the interior push button lock on the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521852-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

Used original door latch actuating rod for either the driver / passenger on the 67 - 68 Cougar.

Used original door latch rod for the interior push button lock on the driver side (left hand) of the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6521853-A.

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1967 Mercury Cougar and Ford Mustang. 1967 door latches are unique, they have a short tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown...

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C5AZ-6223370-A.

Protects quarter panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C4SZ-6323370-A.

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pins. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522811. ...

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior deccor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. These used trim parts will have many very small dings and scratches. The driver side moulding will have substantially more damage than the passenger side moulding. Ford part number C7WY-6220910-A. NOTE: This item will not ship until useable cores are received. ...

Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.

Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.

Driver quality used right side or passenger side folding door handle. This type of handle was used on the 1967 XR7 models and 1968 Cougars. This is also the deluxe handle found in Mustang and other Ford / Mercury cars. Some pitting, will have a good spring and rubber bumper. Sorry mounting screw not included.

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968.  The casting number on the back reads C7AB-5422617-A.

These interior door release handles are the only ones on the market from the 4 different manufacturers that are indexed correctly. They are the updated design for 2019 that fits level and the chrome is excellent. All the other versions either tip up or down too far when placed on the splines. These were used on the xr7 model in 1967 and on all Cougar / Mustang models in 1968. The casting number on the back reads C7AB-5422616-A.

These pressure cast and chrome plated handles are good quality items that are exceptionally low priced. Not show quality or concours correct, but nice replacement. Includes gaskets and hardware. Replaces Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A Also Fits: 1967 Ford Mustang 1968 Ford Mustang 1970 Ford Maverick 1971 Ford Maverick 1972 Ford Maverick 1973 Ford Maverick

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1967 Mercury Cougar standard model 65A or 65C. The 1967 parking brake light kit gets its power from the ignition switch. Ford part number C7WB-10A841-A.

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position. We do offer the correct used Cougar horns.Replaces Ford Part # C7ZZ-13832. These horns are close but not correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B...

Tested and working used Hi tone horn. The High tone is indicated in raised letters located on the perimeter of the horn. 1967-68 Cougars used part number C7WF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.NOTE* - High tone horn is on the passenger side ...

Factory cast iron exhaust manifold set, both right C6OE-9430-E and left C6OE-9431-F side exhaust manifolds. Same manifold for all 289 and 302 engines for both 1967 and 1968. Random date codes.

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation. Our used 390 transfer tubes will often times have a dent or ding in the metal tube. The repro is a very top quality alternative, they would be concours correct in appearance.  ...

PCV TUBE, fits stock GT cast iron manifolds, replaces Ford part number C6AZ-6758-A. The main difference between the 390 tube and the 428 tube is the center fitting angle. The 390 tube has a little less pronounced angle. Fits all 1967-68 S code 390-4V Ford engines. You will need the related fittings for installation.

100% Concours Correct PCV Tube for the 1968 Mercury Cougar 427 GT-E, Ford Mustang, Fairlane, or Torino with the 428 Police Interceptor, fits either # C6AE or # C7AE Aluminum PI intake manifold. Replaces Ford Part #: C6AZ-6758-B.

This fitting screws into intake manifold, has 1/2" nipple for PCV hose, 3/16" vacuum port nipple and threaded hole for smaller accessory fitting. 5/8 by 20 thread pitch

Steel fitting for 390-4V / 427-4V and 428CJ engines with the PCV transfer tube.Replaces C7AZ-9A474-A. Painted Ford Corporate Blue from the factory.

Front steel vacuum fitting for 390, 427, 428CJ engines.Replaces Ford part number C7AZ-9A474-A.

Used brass intake manifold fitting that screws into the rear of the 390GT and 428 CJ intake manifold on all 1967-68 cars so equipped. Similar to the 1969 version, but this one does not have the additional smaller nipple.Replaces Ford part number C8OZ-9A474-A.

Designed for any one-inch hose, this clamp can be used for a number of different applications including the breather hose between the valve cover and air cleaner on 1967, and 1968 Cougars.

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Replaces Ford part #C7AZ-6892. For round hole with two notches, aluminum or steel valve covers.

A needed part for giving your car a tune-up. PCV Valve fits all years; 289, 302, 351, 390, and 428 CID; V8. *Note - Not technically correct for 390-4V or 428CJ, those originally used a PCV valve with a threaded top, and the 90° elbow - part number C7OZ-6A706-A.

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Reproduction positive crankcase ventilation valve or PCV valve for 1967 Mercury Cougar, Cyclone, Ford Mustang and Torino all with 390GT or S code 390-4V engines. This valve has a stamped casting number of C7AE-6A666-B, comes with a white plastic ring as shown. Ford engineering number C7OZ-6A666-A. Also used on 1967 Shelby Mustang GT500, Ford 428PI, and Mercury Cougar GT-E 427-4V engines. *Note - Must be used with either a reproduction or original 90 degree PCV adapter. ...

Reproduction, nice thick firewall insulation pad for the Mercury Cougar or Ford Mustang. We actually like this one better than the "premium" version. These are pre-formed for a perfect fit and appearance and greatly reduced engine noise and heat. The A/C and non A/C versions are the same piece and will fit both A/C and non A/C cars.This pad comes with all the rubber clips needed for installation.

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Easy to replace, keeps correct tension on your gas pedal.

Reproduction kick panel insulation for the 1967 - 1968 Mercury Cougar or Ford Mustang 

Kick panels for the 1967 and 1968 Mercury Cougar that include 6 1/2" coaxial (2 way) 100 watt speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. For some discussion on kick panel speaker options, check out this thread.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.*NOTE* These units may require some slight modification to fit perfectly in your unique Cat or Pony.

Sold as a pair. The overlay bonded to the plastic really gives a feel and look of quality to these kick panels. For more discussion on kick panel speaker options, check out this thread.

Kick panels for the 1967 and 1968 Mercury Cougar that are formed to accommodate speakers. Speakers are not included. These are designed for those who would like to choose their own speakers. Available in black, but can be sprayed to match your interior. Sold as a pair. These now come pre-cut for a 5 1/4 inch speaker. For more discussion on kick panel speaker options, check out this thread.

Great way to update your sound system without cutting door panels or other original parts. Great fit and finish, easy installation. Pioneer speakers are 4ohms, 6 1/2" coaxial (2 way) 160 watts per speaker, for a total of 320 watts max output! Only available in black, but can be painted to match your interior with flexible paint. For more discussion on kick panel speaker options, check out this thread.

Sold as a pair, these are a perfect fit Premium Scott Drake reproduction. Correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers so if speaker holes are needed you will have to use your old panels as a template to drill holes in these "Mustang" reproductions. Replaces Ford Part number C7WY-650345-A1G / Casting number as seen on the back of the driver side will read C7WB-6502345-BW

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Reproduction interior kick panels in parchment / off-white for the Mercury Cougar or Ford Mustang. Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

"Premium" firewall pad for your 67 - 68 Cougar or Mustang. It's "premium" in the sense that it's more expensive. The main difference between this and the "economy" version is that it has a layer of foil inside, which helps with heat insulation. However, the total thickness is actually a little less than the economy version. This may make it easier to install, along with the included hard plastic clips (unlike the rubber originals). Given the significant difference in price for negligible...

Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads

Sold as a pair, these are a perfect fit, correct texture and are less prone to cracking than originals. They do not have the perforated speaker holes for those utilizing kick panel speakers. Check out our custom made kick panels that accommodate modern speakers.

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10841

1967 Mercury Cougar XR7 Instrument Cluster Bezel / Housing Grade A - Used Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the HiBeam indicator bulb. One of the  holes is not used. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the right turn and seat belt indicator bulbs. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Similar to the left turn shroud, there is a locating nub that makes it different. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the left turn and brake system indicator bulbs. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. Similar to the right turn shroud, there is a locating nub that makes it different. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the wiper switch. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle has a blacked out cone as shown. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the OIL light which is the left red light in the FUEL/TEMP gauge. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle is side specific, but resembles the AMPS baffle. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 Standard Model Mercury Cougar. This is for the AMPS light which is the right red light in the FUEL/TEMP gauge. There are a total of 6 of these plastic baffles for a 1967-68 Standard Model Cougar. This baffle is side specific, but resembles the OIL baffle. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with an XR7 dash cluster

Plastic baffle for the instrument cluster on any 1967-68 XR7 Model Mercury Cougar. This is for the Brake system indicator bulb. There are a total of 1 of these plastic baffles for a 1967-68 XR7 Model Cougar, and it goes into the XR7 housing and shares space with the tachometer. Originally, these had a rubber seal on the lip. No more seals. Ford part number C7WY-10A990-_ , exact suffix letter is unknown. *Note - will not work with a Standard Model dash cluster. ...