All Available Parts - 1967 Mercury Cougar

Brass and steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 20 piece set with threaded screw in plugs as shown. 

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Fuel pump drive eccentric for most small block Ford engines 1963-72. Including 221, 260, 289, 302, and 351W. Used eccentric from our wrecking yard. Includes eccentric, bolt, and washer. 2-1/2 inches in diameter.Ford part number C3AZ-6287-B.

Used cover plate or thrust plate that retains the camshaft on the front of Ford small block V-8 engines such as 289, 302, 351W. 1967-70 Mercury Cougar or Ford anything. This plate has three bumps, we have found a Ford number of C9OZ-6269-A, this may be a service replacement number and could be found on engines built earlier than 1969. We have found this style of 289's from 1967. There is another version with Ford number C2OZ-6269-A, it only has two bumps.

Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP

Pair of bolts for installing the fuel pump on most V-8 engines. 289, 302, 351W, 390, 427-4V, and 428CJ. AMK bolts 3/8-16 x 1-1/2 inches. Sold as a pair, for installation of mechanical fuel pump into the timing covers. AMK F-519. 43530-S8.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Used cover plate or thrust plate that retains the camshaft on the front of Ford FE big block V-8 engines such as 352, 360, 390, 410, 427, 428, and 428CJ. 1963-70 Mercury Cougar or Ford anything. We have found a Ford number of C3AZ-6269-A, 

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Concours reproduction with FoMoCo rectangular stamp. Used on all 1967 - 1973 models with 2" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

New Dual Transverse Muffler as used on the 67 Cougar with 390. This muffler is an exact match (connection wise) to the factory Ford OEM Transverse muffler that is no longer available. Muffler dimensions: 20" x 11" x 4 1/2" Aluminized SteelSeam Locked like the originalsSlightly increased flow over stock mufflerAuthentic dimensions to OEM mufflersStock dimensions for absolute proper clearances ...

Reproduction pair of exhaust pipe clamps for your 67 - 69 Cougar or Mustang.

Reproduction hex screw for exhaust pipe clamps for the 1967 - 1973 Mercury Cougar and Ford Mustang. 5/16 x 1-1/2 screw. Fits original and new clamps.

Reproduction Upper Control Arm To Shock Tower bolt.  Sold individually. Replaces Ford part # 38049-S

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Reproduction bolts and washers for the manual transmission bell housing on any 67 - until 2/1968 Cougar or Mustang equipped with a 390 / 428.

Reproduction set of four 2 3/4" black phosphate bolts for the 2 1/4" fan spacer on the 67 - 73 Cougar or Mustang.

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Spring nut used to install the fan shroud on a 1967-71 Cougar or Mustang, 4 per car.

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

This listing is for anyone who wants to order a custom set of floor mats. Simply add this item to your cart, and in the order notes section of your order, let us know which carpet color you want (please choose from the available options in color sample photo above or if ordering at the same time as a carpet kit simple say "please match ordered carpet color") and which script you would like, whether it be the Walking Cat, Cougar Head Logo, XR7, The Cougar Script or the GT...

These floor mats were available as part of the factory "protection package" or as a dealer accessory when these cars were new. Good used originals have gotten VERY hard to find. At present (9-20-18) they are only available in black. Keep in mind the 69-73 convertible used a narrower mat to clear the inner rockers. We have a diagram that shows you where to trim for your convertible. The walking Cougar logo is a favorite of any Cougar fan. The Cougar became so popular that soon after the Cougar...

Reproduction sound deadener for the seat divider on the 1967 - 1970 Mercury Cougar. This reproduction is as close to the original as possible, and is comprised of a mastic material. This item is trimmable and will fit bot the 67 - 68 and 69 - 70 seat divider.

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair

Used grade "C" driver side (left hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

Pliable, soft used trim with no burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

Mostly Pliable, may have small burns or nicks. 1967 is actually the same as 1968 but 1967 had a coat hook installed over the trim and it leave a permanent indentation that will not come out. If your wind-lace has shrunk up a little you probably will not be happy buying ours as most all of them shrink a half inch or so and it will be most evident where the trim tucks behind the rear interior panel. To "stretch" your moulding a little, hang it from your eves on a hot summer day and hang a brake...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

This will really help you understand how your column works! Covers operation, tests and adjustments. All Mustang / Cougar tilt columns were tilt-away in 1967 - 1969. This manual is free for the asking when you purchase a tilt column from us. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most...

Chrome center caps with black background and chrome Mercury man logo.  Came from the factory on 1967 and 1968 Mercury Cougars with Style Steel Wheels, but will work on any 67-70 with Style Steel Wheels.Fits the following models with style steel wheels: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury CougarOther Mercury Cars These caps measure 2 1/2" wide by 9/16" tall. These have been obsolete for many years and often we find deterioration on them even though...

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

NOS hubcap / wheel cover that is new in it's original Ford box for your Mercury Cougar.Ford part # C7WY-1130-B This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash...

This is a NOS clock. The face is brilliant, it has never been mounted and is guaranteed to work good. It does have a tiny crack that is mostly hidden by the center knob which is very common for these original lenses.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

This used power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid.This relay also used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.

NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

C7ZZ-7528-G NOS clutch equalizer or Z - Bar, or bell crank for 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and either 3 or 4 speed manual transmissions.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This trim ring was used in 1967 and is very close (not as deep) to the 1969 - 1970 trim ring. 1968 was deeper and was brushed on the inner portion. 1967 Cougar style steel wheels are 14 x 5.5" wide and 1.75" deep. Ford Part number C6ZZ-1210-A.

C7WB-13713-A New old stock XR-7 dash toggle switch for the "Panel" light on the 1967-68 Cougar. This switch has the black plug, and it will work for the "Courtesy" light switch too, those are typically have red plugs though.

Referred to as the "K10" relay in the Ford Service manual. The emergency relay, when energized, maintains through circuits from the motor and cam assembly to the rear lamps. During emergency flasher operation, this relay opens the circuits (normal position) to the inner and outer rear signal lamps. Thus, only the center rear lamps operate when the emergency flasher system is functioning. This unit was originally mounted to the underside of the black cardboard trunk filler board on the driver...

Very Limited supply. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.

We have a very hard time keeping these NOS rear lower valences in stock. Since the reproductions don't quite fit right, NOS and good used are the best options at this time.Ford part # C7WY-6540544-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...

New old stock part. Fits 1967 Mercury Cougar XR7 models.  Ford part numbers: C7WY-17A553-B and C7WB-17A553-B

This is known as the "K6" relay in the Ford service manual. The function of this relay is to open the circuit between the two instrument panel turn indicator lamps during normal turn signal operation. During emergency flasher operation, the relay points are closed (normal position) and the two instrument panel indicator lamps flash at the same time. Ford Part # C7WY-10B926-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on...

NOS new old stock . This unit is known as the "K5" relay in the service manual and is stamped with C7WB-13A366-B. The turn signal indicator relay switches the indicator light circuit so that the left indicator lamp on the instrument panel flashes for left turns and the right lamp flashes for right turns. Application is 1967 Mercury Cougar. This unit (and subsequent system) is an inherently weak design. Make sure your ground wires are clean and connected firmly and all your light sockets...

This is referred to as the "K7" relay in the Ford service manual. This relay causes the flashing action of the 1967 Mercury Cougar instrument panel indicator lights. The number stamped on this relay is C7WB-13A366-A, the Ford part number is C7WY-13A366-C. A quick bench testing: There needs to be continuity between the 'H' post NOS item, new old stock.       *CAUTION* The 1967 and 1968 K7 relay look similar, but are not the same. Damage to your wiring system will occur...

New old stock dash toggle switch that operates the passenger side (right hand) map light in the Mercury Cougar XR7. These switches will have no rust or broken wires and the plastic toggle switch tips are sold separately. These used switches move freely and are guaranteed to work. The only real difference between the years, besides the size of the shaft, is the toggle switch tips.  There are three versions of shafts used on the 1967 - 1968 XR7 toggle switches and all three feature the same...

NOS relay for 1967 Mercury Cougar or Ford Mustang with factory speed control. This is the anti retard relay, identified with the plug with two male connectors. Mounts to the Regulator mounting bracket along with the Brake Release Relay. May also be correct for 1968, we are not sure. Ford part numbers C7WA-9C733-A and C7WY-9C733-A.

New old stock part. Fits 1967 Mercury Cougar Standard models.  Ford part numbers: C7WY-17A553-A and C7WB-17A553-A

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

These are good reproductions of the originals for your American Sunroof Corporation Golde Sun Roof. The roof opening seal is 89 1/4" x 3/4" and the seal that affixes to the rear edge of the roof panel measures 42 1/2" x 3/4". These have the correct aluminum inner core with rubber bead, wrapped in the correct felt textured, black material. They're are made by the original manufacturer in Germany and will fit all Cougars equipped with the ASC sunroof. Very hard to find seals at a reasonable...

Rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors.Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B Check out our...

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s...

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

NOS brake pedal for the Mercury Cougar or Ford Mustang equipped with power drum brakes. This unit will work with disc brake Cougars and Mustangs, but is not correct. That is because the power drum pad has "power brake" inscribed on the pad where the disc brake version has "disc brakes." Also, the 1967 version is narrower than 1968-73 piece.Ford part # C5ZZ-2457-E.

Excellent fit whether you are installing OEM thickness glass or repro which often is a slightly thinner gauge, must have when replacing either headliner or windshield. There have been multiple manufacturers of this seal over the years, this is the best fit in our opinion. Fits years 67 - 68 for Cougar and 65-68 on the Mustang. We also sell the bedding compound for the installation.  Replaces Ford part # C6ZZ-6503110-A. Keep in mind this is not a difficult do-it-yourself project, here's...

Nice fit! You will need new window gaskets if you plan on changing the headliner. If you are installing the gasket yourself, you will be needing a bedding compound, we like this one here. Replaces Ford part # C7WY-6542084. You can get a feel for what it takes to replace your rear window seal by watching our windshield replacement video. Check out this video

Parking Light Lens Seals are sold as a pair. Fits the 67 and 68. Replaces Ford part #: C5ZZ-13211.

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

These Back Up Light Lens Gaskets are sold as a pair. Fits the 67 and the 68. Replaces Ford part # C5ZZ-15510.

The correct color for the Cougar was gray but many prefer these black Mustang gaskets. Sold as a pair.

These Back Up Light To Rear Valance Seals are Sold as a pair. Fits the 67 and the 68. Replaces Ford part #: C7ZZ-15533. Note, gray is in fact the correct color for these, Mustang used black in 67-68. Note we also have black available for those who prefer.

Reproduction taillight housing to body seal kit for the Mercury Cougar or Shelby Mustang. Sold as a kit for two lights. Replaces Ford part # C7WY-13520.

Sold as a pair. These seal the lens to the taillight bucket / backing plate. Also used on the 1967 Shelby. Replaces Ford part # C7WY-13461.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.

This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.

This Wiper Pivot To Cowl Seal Reproduction is sold as a pair. Fits both the 67 and 68. Replaces Ford part #: C5ZZ-17475.

Unfortunately the premium version is no longer available.  This version is made of a softer compound than the original bumpers and will not hold up as long as the originals did on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Check out this video Check out this video

Reproduction license plate / fuel door cover rubber bumpers for the Mercury Cougar or Ford Mustang. These will also work for the 1969-70 Mercury Cougar or Ford Mustang cowl cover to hood rubber bumpers. Sold as a pair with the mounting screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate substitution. If you really need an exact replacement we sometimes can provide a used bumper. ...

Four per car, mounts to fender. Sold individually. Replaces Ford part #: C7WY-16758.

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

For the in-dash ashtray.

This little rubber part attaches to the top, flat part of your center grille and keeps a small gap between the two panels to prevent paint chips. This is actually an ash tray bumper but it is a decent substitute (a little smaller than the original) for the center grille bumper. The originals had a flat top as opposed to this bumper which has a rounded top. You can find the flat topped version here. ...

Sold individually.

Comes with attaching staples made of stainless steel. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. Replaces Ford part #: C4DZ-16238.Not all cars were assembled with this seal, some came with staples, and others used clips.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

Reproduction 5/16" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C5ZZ-9288.

This kit includes 33 pieces and has the quarter panel drain valves.

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the budget or economy versions. We also sell concours versions.

These are a higher quality rubber than the other reproduction available. Mounts to the door jamb and keeps water from going into the quarter panel. Sold as a pair. Replaces Ford part #: C7ZZ-6528182 and C7ZZ-6528183

Reproduction door to window seal for all 1967-68 Mercury Cougar and Ford Mustang. Technically though

Complete Heater Seals And Foam Kit. Replaces Ford part #C5ZZ-18500.

Complete foam seal kit for the heater box, flappers, evaporator and heater core on a '67-'68 Cougar or Mustang with factory Air Conditioning. This kit is almost always needed when replacing your heater core.Replaces Ford part #: C7ZZ-18500-A. Check out our video below on how to replace a heater core on a '68 Cougar with A/C! This seal kit is an integral part of the process. ...

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...