1967 - 1968

AMK engine fastener kit for 1967 Mercury Cougar and 1967 Ford Mustang all with C or A code 289 engines with air conditioning. This kit claims to have 126 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

AMK engine fastener kit for 1967 Mercury Cougar and 1966-67 Ford Mustang all with C or A code 289 engines without air conditioning. This kit claims to have 122 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water...

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

AMK engine fastener kit for 1967 Mercury Cougar / Comet, and Ford Mustang / Fairlane all with S code 390-4V or 390GT engines. This kit claims to have 133 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

AMK engine fastener kit for 1968-69 Mercury Cougar and Ford Mustangall with S code 390-4V or 390GT engines. This kit claims to have 138 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck, water pump,*Note -...

AMK engine fastener kit for 1968 Mercury Cougar / Comet, and Ford Mustang / Fairlane all with R code 428 Cobra Jet engines. This kit claims to have 145 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water neck,...

Fits Standard and XR7.Made in the USA

Reproduction body / exterior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Hood Bumpers (adjustable) Hood Latch Dowell Valance (front) Valance (rear) Door Hinges Floorboard Hole Covers Fenders Fender Splash Shield Brackets Hood and Hinges Shock Tower Braces Cowl Brace to Cowl...

Reproduction master interior fastener kit for the Mercury Cougar Standard. This kit contains 264 fasteners in total. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Armrests (front) Armrests (rear) Scuff Plates (door opening) Sun Visor Brackets Glove Box Catch Glove Box Latch Glove Box Liner Ashtray Liner Seat Stops (front of seat backs) Mirror to...

Reproduction master interior fastener kit for the Mercury Cougar XR7. This kit contains 297 fasteners in total. *NOTE* If you click on the selections below, they will take you to each of the sub kits that are included in the main fastener kit. In this kit you will receive the following fasteners: Armrests (front) Armrests (rear) Scuff Plates (door opening) Sun Visor Brackets Glover Box Catch Glove Box Latch Glove Box Liner Ashtray Liner Seat Stops (front seat backs) Carpet to Floor (carpet...

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

This is a 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from a substantially better grade of steel than the originals. These often break when you try to remove them to replace the vacuum actuator so if you are planning on doing that procedure we highly recommend buying these in conjunction with the actuators. Sold individually, two required per car. Cougar part number C7SZ-13A173-A. Also Fits: 1967 Ford...

This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort. Cougar part number C7SZ-13A173-A. Application includes: 1967-68 Mercury Cougar and XR7, 1967-68 Ford Thunderbird, 1969-71 Lincoln Continental MK III. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in...

Sold individually. Phosphate & Oil (gray-black)

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Fits 1967 Standard and XR7 Cougars or most Ford and Mercury with inside rear view mirrors. Also used on the 1967 xr7 hash marks located on the rocker.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

Replaces Ford Part # 381985-S Sold individually

Self threading speed nut for attaching "COUGAR' scrip emblems to the rear quarter panel of any 68 - 70 Mercury Cougar. Sold individually, 4 needed per emblem. Whereas these work fine, the originals were an acorn style nut and look very different.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. These are sold individually.Replaces Ford part # 373556-S. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

These were used to attach the taillight assembly to the tail panel on a 1969-70 Cougar. Five were used per taillight, 10 required in all for one car. Sold individually. Also the same size for 1967-68 tail lights.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...

These are the little 11/32" lock nuts (sometimes called speed nuts) that you use to attach the taillight bezel to the taillight housing. 10 nuts per bezel, 20 per car.

Reproduction pair of snap nuts for attaching the hood latch support to the hood latch on the 67 - 68 Cougar. 

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...

New pan head screws for installing the automatic console shifter bezel. Sold as a set of 4. Used in conjunction with the 3 metal strips to attach the automatic shifter bezel. Correct black pan head Phillips screw. *HINT - The metal strips can be made from any strips of steel, they don't really need the edges folded if you don't cinch them down too tight. Metal strip should be 1-11/16" x 5/8" with a hole in the middle.

Reproduction Pitman Arm w/ 1" Sector Shaft Nut EACH for the 1967 Mercury Cougar or Ford Mustang

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

This plastic protector sleeve is often missing or broken, but occasionally we come across a good used one. This part attaches just in front of / below the fuel tank on the passenger side, and serves two purposes: it routes the wiring closer to the fuel sending unit without it dangling down, and protects it from road debris This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Fits 1968 Standard or XR7. Has a pair of longer screws for the 1968 lower section of the door panel. 

Four needed per fan shroud. Sold individually.Ford Part Number: 383152-S

Four needed per fan shroud. While not technically correct, some like the black screws over the silver because it better matches the radiator and shroud. Hexwasher Head #14 X 5/8 Tapping Screw Ford Part Number: 31498-S

Four needed per car. Ford Part Number: 31498-S

Reproduction Radiator Mount Kit for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Reproduction Rear Bumper Guard Bolts & U Nuts for the 1968 Mercury Cougar 

Replaces Ford Part #: 379670-s

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Replaces Ford Part # C8AZ-2066-A Sold individually

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet. Sold individually. 2 rollers required per window, 4 rollers required per car. Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" Diameter Here's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: ...

These small rubber protectors slip over the metal tabs in the trunk that hold the taillight wiring loom to the body. They protect the wiring from abrasion, and are often missing. Sold individually.