1967 Ford Mustang

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

Used Servo Assembly for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C735-A.

Used servo cover from a 1967-68 Ford C-6 transmission. This cover has the big H cast into it, which designates it as an "H" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, with Mercury Cougar and Ford Mustangs with S code 390-4V engines. Cover only, marked C6AP-7D027-D.

Used Shaft for the bell crank on the 1967-68 Mercury Cougar and Ford Mustang with speed control. The Shaft attaches to the Servo Bracket. It Bell Crank pivots on the Shaft. Ford part number C7ZZ-9D768-A.

C8ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. May be either large or small trunion. Subject to availability. Check out our video on rebuilding your shifter below: ...

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

Factory detailing and triple chrome plating distinguish this tubular shift handles from the rest. Cable and T-lever included. American made for quality workmanship. Replaces Ford Part #: C5ZZ-7210-M. Check out this video Check out our video on rebuilding your shifter below: ...

Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only. 

C7ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. Check out our video on rebuilding your shifter below: ...

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

1967 - 1968 Manual 3 Speed Shifter Mechanism - Used C5ZZ-7400-C 3 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Check out our video on rebuilding your shifter below: ...

C7ZZ-7400-C 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

C5ZZ-7210-D "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1967 Mercury Cougar and Ford Mustangs with the 3 or 4 speed shift lever, and 1968 shift levers through 1-2-1968. Bottom bracket only, called a Trunion (see illustration). Measurement of hole spacing is 1-13/16 inches on center. *Note - Must be used with 3 speed shift lever C5ZZ-7210-C, or 4 speed shift lever C5ZZ-7210-M. Check out our video on rebuilding your shifter below: ...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

If you want to install factory shoulder belts on your 1967 Cougar or Mustang, you need to install these shoulder belt brackets. It's a threaded block inserted into the clip that holds it in place. 67 Cougars and Mustangs didn't come with shoulder belts, but the raised area where these brackets attach is still present. Simply clip the bracket in place. Now you've got what you need to bolt that shoulder belt in place. Keep in mind that you need to have the correct lap belt configuration to be...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out our video on rebuilding your shifter below: ...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Used spacer for the lower windshield moulding

Early version of the FE engine / Transmission spacer plate. Has 1 medium sized hole instead of 3 smaller holes above the crankshaft. Originally was for either automatic or manual. Ford part #: C3AZ-7007-A.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with 4 speed transmission. These are assembly line used and would have had a Ford number of C7ZF-17260-A or C7ZZ-17260-J. Has captured hold down bracket at transmission. Cable has a rubber hose at the transmission end. These measure out about 76 inches long. Also has a metal sleeve about 10 inches from the speedometer cluster end, Cable clamp? Used condition, will have road grime, and maybe a couple of abrasions or small...

Used speedometer cable from a 1967-68 Mercury Cougar or Ford Mustang with C-6 automatic transmission. These are assembly line used and would have had a Ford number of C7ZZ-17260-C. Has captured hold down bracket at transmission. About 66-9/16 inches long. Used condition, will have road grime, and maybe a couple of abrasions or small cracks in the casing. The internal cable has been tested and is good. Tags generally are not present on these. Look at the related items, you may need a firewall...

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *NOTE* This bracket is a bit shorter than the 4V version.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.

"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.

Used 14x5" stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. These were offered in 1967, we believe that a 5-1/2 inch wheel was used starting in 1968-69. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.*Note - these wheels will not work with disc brakes...

Used 14x5-1/2" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. We save some of the better stock wheels and some have probably ridden in trunks most of their lives. This 1967 specific wheel is slightly different than the more common 1968-69 stamped steel wheel. Limited to stock on hand. These were offered from 1967 through 1969. Have a bent or damaged wheel? Don't have a spare? Shipped bare. Various conditions and subject to availability. Used 'as is', wheel as found in the...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. These were offered from 1968 through 1970. Produced by Motor Wheels, early ones had riveted centers, changed to welded centers in 1969. Specify in the notes section if you have a preference, we seem to have mostly welded ones at the moment. Have a bent or damaged wheel? Don't...

Used 14x6" stock stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will ever find due to our mild climate and some have probably ridden in trunks most of their lives. This were offered in 1967 with S code 390-4V option. Hard to find the 1967 manufactured version, we generally have the 1968-70 wheels, but they have a different center section. Have a bent or damaged wheel? Don't have a spare? These wheels will fit over front disc brakes....

NOS Standard seat belt retractor including bolts and a huge 44" x 33 1/2" Ford seat belt diagram in FoMoCo box and never installed on a car. Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models.  NOTE: Front retractors are same for left and right. Check out our video "All about...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Used strap or support bracket for the foam air conditioning vent tube going to the passenger side A/C vent. The electrical assembly manual indicates that two of these strap brackets were installed above inside the dash above the glove box. Our findings from the wrecking yard show that zero or one may have been installed. We have found a single bracket, no doubles, if at all. This part will seldom be in stock, but is fairly easy to fabricate. Find some 1/2 inch wide thin steel and cut a piece...

C7ZZ-5482-B This is a factory used front sway bar. This is the same size 3/4 inch diameter as the 289 and 302 sway bar but has a slight difference in the bends for the 1967 390-4V or 6.5Liter engines. This bar was factory identified with a One-Yellow and One-Blue paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.