1967 Ford Mustang

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.

Used plastic rocker moulding clip for 1968 Mercury Cougar and 1967-68 Ford Mustang. Used clip, originally pop riveted onto the rockers. Sold individually. Ford part number C7ZB-6510182-A.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2".  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

This clip fastens the vacuum motor to the locking pawl rod. One required per car. Fits 1967 Ford tilt-tilt away columns only. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired.

This reproduction roll up door for the Standard Mercury Cougar's center console features a bright finished metal front on flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Replaces Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being...

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front and flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang...

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction of the very hard to find window roller for the window channel / quarter window frame on the 67 - 68 Cougar and Mustang. Doubles as both the single and double type roller (with the included support washer).Included in this kit are: One roller, one rivet, one wavy washer, one flat washer, and one support washer, measures exactly 1" wide. Rivet is for a 1/4" hole.2 required per door glass channel, 3 per quarter window frame.Sold individually. Replaces Ford Part # C8SZ-57262A32-A....

Used roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Also found on all 1967-68 Mercury Cougar and Ford Mustang door window channels. Often times one of the rollers breaks off and allows chattering of the window movement. Sold individually: 3 total rollers on each side of the quarter window brackets. 2 like this

Replaces Ford Part #: C0AB-6423240-B. Four required per car, two per side. If your quarter glass is loose in the track and will not roll up and down these rollers are most likely the culprit. When the tracks get gummed up and the window takes too much effort to roll up and down, these brittle old rollers will break. Even if they are not broken they are often frozen in place from rust and will not spin freely. From our experience every 1967 - 1968 Cougar needs these replaced if they still have...

Used single plastic roller for any 1967-68 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Note that there is only one of this style of roller on each quarter window. This is a simple white plastic roller and a rivet. Note that there are 2 rollers with 2 pieces of round white plastic. Often times one of the rollers breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

Reproduction roller control arm assemblies. These control arms are a slightly modified version of the 67-73 lower control arms found on Cougar and Mustang. A roller bearing has been added at the mounting point allowing them to move up and down, laterally and also allows for a small amount of twisting. This creates smoother handling. Sold as a pair. NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

Used spiral bound Rotunda oil and lubrication guide book for 1967 Lincoln Ford Mercury vehicles, including Ford trucks, Econoline vans, Thunderbird, Falcon, Fairlane and Bronco of the same year. Included information on oiling and lubricating everything from the the chassis to the engine and cooling system. Volume 67 PS 5L8  

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

These were installed only on early production 1967 Cougars but can be installed on any 1967 Cougar. Later in the year they quit installing these and just used a rubber plug to fill the hole. 1968 was not drilled for these. Sold as a pair.

New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily. *NOTE* This item can only be shipped via UPS ground. No Foreign orders please. Check out this video ...

Good grade A used jack with correct fine threads. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not. Grade A will not have rust or damage.

Good used jack with correct fine threads. Notice the remnants of the original jack instruction decal. The most common jack as identified by the fine threads. This version was made by several suppliers, and may have slight variations from the picture. Some have date codes and some do not.Grade B will have Rust and or the top portion letter "M" fitting may be damaged.

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold individually, three per side, six per car required. These often get destroyed when you go to replace your door window regulator slides. Three of these are used to install the C7ZZ-6523288-A track. Stainless steel.Thread size: 8/32 Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator?...

New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually Zinc Dichromate (yellow-rainbow)

Sold individually. Zinc (dark silver)

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Also sold individually.

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used unique Phillips bright finish screw that attaches cable guides to roof.

This is a very specialized screw that you do not want to fail or make do with an incorrect fitting or stripped screw. When removing your old screw you will most likely have to pull your pedal assembly and have a perfect fitting screw driver to remove the screw as the factory put them in 3-6 foot lbs.Ford part number 380503-S8.

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Screw for mounting wing window pivot bracket. Two per car