1967- 1968 Seat Tracks / Seat Hardware

Ford Part # 379390-s Sold individually

Includes a pair of chrome screw adjusters, nuts and washers, heavy duty plastic rest plates and attaching screws to repair or replace that missing seat back adjustment.Replaces Ford Part #: C1DZ-6461643

Fits 1967 Standard or XR7

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Fits Standard or XR7. Sold as a pair.

1969-70 actually used a star head bolt but these are a much more user friendly screw that will work in its place. Sold in a set of four which is what you will need for one seat.

Pressure die cast with show quality chrome. Easy to install, correct fit and finish, inexpensive way to spruce up your interior. Remember when we used to send these out and pay big money to have them replated? Sold as a pair, hardware included.

Fits 1967 and 1968 Standard or XR7. Holds "J" shaped plastic hinge covers in place.

A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat back when positioned forward. This bracket carries a D7AA-69618C46-A or D7ZZ-69618C46-A service replacement part number. Without...

Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.

The knobs for the seat track release to adjust the position of the seat. The reproduction has a slightly deeper divot where you place your finger, and is slightly more round on the bottom, but a very nice reproduction. Replaces Ford Part #: C5AZ-6261753-BA.

These are often cracked or collapsed causing your seats to lean back too far. One kit does one seat, two kits required per car.*NOTE* Don't discard your original screws! The screws supplied with this kit have a head that is just slightly smaller than original so when you really tighten the screws down the head goes right on through the stop! A very small washer will cure the problem if you choose to use the screws supplied. Replaces Ford Parts #: C8ZZ-6560310 & C8ZZ-6560311

Fits 1968 - 1970 Standard or XR7

The bench seat brackets are slightly different than the bucket seat brackets. Our premium grade used tracks are carefully inspected for damage before shipping. Most likely you will have to paint but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. Ford master part numbers...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Correct for 1967 but fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. We also have the version with rectangular plates at the studs if you are wanting to match what you may have currently. ...

This Grade B set will need clean up and servicing but will not have cracks, broken studs or excessive rust. Fits all 1967-70 Mercury Cougars including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version.

Comes with all parts shown for one bucket seat, good quality but not as good as original FoMoCo parts. Make sure and check out our good used originals. Replaces Ford part numbers C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A.

This adjustable linkage kit connects the left track to the right track on a bucket seat. Original Ford part number C5ZZ-6561726-A. Ford description: Rod - Front Seat Track Tie. Listed for bucket seats 1965-1970.

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Sold individually.Replaces Ford Part # C5ZZ-13190-K

Sold in a set of eight, these are the same gauge steel as originals. Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Replaces Ford Part # C5ZZ-13190-K

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

Installs between seat track and carpet. These are the same gauge steel as originals. Four per bucket seat, normally only seen on the 1967 model year, will need to be restored. Reproductions work fine, but look a little different. Ford Part # C5ZZ-13190-K