Steering

This clip fastens the vacuum motor to the locking pawl rod. One required per car. Fits 1967 Ford tilt-tilt away columns only. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired.

Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

If your power steering control valve unit is in good working condition but seems to be leaking, this seal kit may be all it takes to correct the problem. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. We also have the complete rebuild kit available.  NOS power steering control valve seal kit.  Ford part number C3AZ-3A650-B. ...

If your pump works fine but leaks this is an easy kit to install. Replaces Ford Part #: D1AZ-3B584-A.

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.

Reproduction spool for the control valve on your 67 - 70 Cougar or Mustang.

Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

This is a tension spring that defaults the steering wheel to up and or tilt away position. The spring in the 1967 Column is not as strong nor as tall as the 1968 or 1969 column spring.Spring Length: 2 5/16" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Reproduction Stabilizer End Link Bolt for the 1967 Mercury Cougar - 1967 Ford Mustang

Now an inexpensive and easy way to convert 1967 - 1970 power steering cars to manual steering. This will give you a more precise feel for the road or track. Eliminates leaking systems and costly repairs. Installs in minutes with no special tools.

This is the most complete kit available for the steering box with 1 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your EARLY short shaft 1967 Cougar or Mustang steering box only with the 1 inch diameter sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a...

This is the most complete kit available for the steering box with 1-1/8 inch sector shafts. Comes complete as shown. Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can...

Reproduction rebuild kit for your 67 Cougar or Mustang steering box. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. Early 1967 Steering gear boxes with 1 inch sector shafts. Sector shaft is where the Pitman arms attaches.

Reproduction rebuild kit for your 1967-70 Cougar or Mustang steering box only with the 1-1/8 inch sector shafts. Needless to say, having a faulty steering box can be quite dangerous. If you hear grinding or popping sounds coming from your box, it may be time to rebuild it. We do offer a rebuilt steering box, but if you're good with your hands and on a budget, you can rebuild your box with this kit. SMB-K, SMB-D, and SMB-F tagged steering boxes. Probably a DIY youtube video out there for...

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Fixed steering column from a 1967 Mercury Cougar. Reasonably rust free column that ships as shown in picture. Often we will leave the turn signal switch in place, but you should count on it being non functional. This steering column will fit a Mustang, but you must change steering boxes. Most 1967 Mustangs came with the steering box with the long spear. Upper and lower mounting brackets, and rag joints are available, but sold separately.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

Reproduction steering column flange bumper for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This flange is made of a material known as UHMW, or Ultra High Molecular Weight plastic. This material has been used by NASA for many parts that were formerly made of nylon. This material is five times stronger than nylon, and has a much higher impact rating. Compared to the original nylon part, this piece should not have to be replaced for a good number of...

Used steering column flange bumper for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This little unit is made of plastic and Ford used it to keep the tilt / tilt away steering column's flanges in the knuckle assembly from breaking its self apart during actuation. Because of the forces generated in the tilt / tilt away column's actuation, your knuckle assembly will fail due to metal to metal contact if this piece is missing. Ford part # C7SZ-3D565C....

This reproduction steering gear box is for manual steering cars and has a 16:1 ratio, it also has a 1 inch sector short shaft for the Pitman arm.  *The SMB-C was known for breaking sector shafts. There was a factory recall on the SMB-C and they were replaced by the SMB-D. If you are trying to identify the proper steering box, the box will have a raised casting number of C7ZR-3550-A. The early (prior to approximately 5-1-1967, 01E date on the data plate) steering boxes (both manual...

These are PREMIUM GRADE rebuilt steering gear boxes for the early 1967 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a true...

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

Rebuilt steering gear box with 16:1 ratio and 1 inch sector shaft. These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box...Our boxes are rebuilt here in the USA at...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm.These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will...

These are the newest steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be a great buy because of the fact that they come with a lifetime guarantee. These gear boxes are not rebuilt, as are the rest of the boxes we carry, so there's also no core charge. 16:1 ratio NOTE* The supplier specifies that these steering boxes are made with new and used parts. Having issues with wobbly or loose steering? Check out our video on sloppy steering...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

Reproduction Chrome / Black Leather four spoke steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and walking cat center decal. Hardware included.

Reproduction Black Steel / Black Leather steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

This is a reproduction steering wheel for a 1967 Mustang with Deluxe interior. It makes a nice substitution for the 1967 Mercury Cougar wheel and since the 1967 Mustang used the same steering columns (both fixed and adjustable) you are guaranteed a factory correct fit with no issues making your horn or turn signal cancellation work properly. This steering wheel is being offered without a horn center / pad. You can use your original Cougar hub, which fits perfectly without modification. If you...

Replaces Ford Part #: 350983-S

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

Brand new WCCC exclusive! These 1967-only steering wheel center emblems have been needed for some time. Most originals are faded, scratched, and often warped or broken. These new ones fit perfectly in your original center pad and look great. Watch our video below to see how to replace your old emblem and trim ring with our new ones. ...

There are three of these rubber, glue on pads attached to the chrome horn center of every 1967 Cougar. The colored pads usually need to be repainted and we cannot guarantee to have all colors in stock at all times. These pads are sold individually, please select the desired color and we will try to accommodate you. Check out the very first Cougar in our video below! ...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...

The Mercury Cougar used this articulated strut rod in 1967 to help give the Cougar a little softer ride over the Mustang. It is debatable just how much the addition of this joint helped. Many people choose to switch these struts for either 1968-69 or 1970-73 strut rods. The main reason is to be able to utilize the reproduction 1968-73 lower control arms, the second reason one would move away from this one year only, cougar only rod is that it is difficult to rebuild. We only sell grade "A",...