Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 18503 -
1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27504 -
Used 3/8-16 x 41/64" carriage bolt for the shock tower shock cap. Three bolts used on each cap, 6 total per car. Sold individually. *Note - Carriage bolt detail cleaned for the picture, actual part will need a clean up on a wire wheel.Replaces Ford part number 378535-S2.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 31622 -
New castle nut for all power steering control valve ball stud found on 1967-70 Mercury Cougar and Ford Mustang. 3/4 inch hex nut, with 1/2-20 threads. Connects the Pitman arm to the ball stud on the P/S control valve. Don't forget the cotter pin. Verify your shop manual for correct year torque specifications. We found one source of 28-35 FT LBS. for the Pitman Arm nut to control valve. Ford numbers for attaching nut: 1967-68 351059-S, 1969-70 385002-S.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 24262 -
C7ZZ-3304-A Manual steering drag link for any Cougar or Mustang from 1967 - 1968 with a non-power assist manual steering system. *Concours tip - This is a natural cast iron part that originally had a pink stripe for identification on the assembly line.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 24263 -
Power steering drag link for any Cougar or Mustang from 1967 - 1968 with factory power steering system. *Concours tip - This is a natural cast iron part that originally had a yellow stripe for identification on the assembly line.Replaces Ford part number C7ZZ-3304-B .
Wanted!
Featured!
Buy
Details
Availability: In-Stock Item
Item #: 26096 -
Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III.
NOTE: The direction of flow is up through the dual ports and out through the single port.
For more in depth detail on this reproduction, see pictures below.
*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19023 -
This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 15-0055 -
Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41271 -
Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0053 -
Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place. * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0061 -
Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 14027 -
Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0032 -
One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0033 -
This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 14035 -
This complete four piece kit is for any small block 289, 302, or 351 Windsor Cougar 1967, 1968 and 1969.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 31880 -
This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 31881 -
This complete four part kit is correct for any 1969 small block 351 Windsor Mercury Cougar or Ford anything 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut. If you do not have a air conditioning you will need a the rectangular spacer which is sold separately.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 25923 -
This unit was used only one year on the Cougar and is unique because of its smaller fitting (1/4") for the pressure hose. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. We highly recommend upgrading to the large nut (5/16") control valve as the small nut control valve posses a potential safety issue, thus the reason why Ford replaced it the following year. The small nut system was engineered dangerously close...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0074 -
Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41036 -
Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41331 -
Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11784 -
Reproduction power steering drop bracket for the Mercury Cougar or Ford Mustang. One must use this part when installing headers with power steering. Because of the way this bracket hangs down, it will get bumped and bumped hard in time. Becasue of this we recommend considerning our premuim version of this bracket, as it is substantially stronger.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11795 -
Installation of this bracket is easy but you will have to make a spacer to fit on the outside of the frame rail. Hopefully you bought this bracket first before you tore out the nut inserts in the frame. If not you will need to get them up for now. Then tap the bracket toward the the outside of the car and make sure the cross bolt lines up. Then measure the gap and make a spacer to fit. A half inch nut and a couple of washers usually work just fine. It's not necessary to get fancy with this...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 13989 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Not correct for 1967 but works as a functional substitute. This vacuum reservoir mounts under the battery tray for factory tilt swing away steering columns found in the Mercury Cougar or Ford Mustang / Thunderbird. Note that some 1968 Mustangs (without air) mount this tank on the passenger side rear apron. This is a double nipple tank, we also sell the single nipple tank for the...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 12283 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Reproduction vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that didn't have mounting bolts on top like the later versions, they used a side mounting bracket.NOTE: You will need to use the mounting bracket from your old can, these reproductions do not come with one. *NOTE* WCCC services all FoMoCo tilt...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0042 -
Mates vacuum nipple on white plastic vacuum motor to ninety degree metal elbow.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19181 -
Good used emblem that is not warped and still has the silver paint intact. Don, Thought you might like to see another success story due to help from W.C.C.C. Attached is a picture of my 67 XR7, Lime Frost with Saddle interior. Thanks for all your help and advice. You and your team made a dream come true. Jim Kohler Check out the very first Cougar in our video below! ...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 15-0096 -
Used Emergency Flasher Knob Bezel / Fixed Column for the 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26089 -
Easy screw in replacement with correct chrome finish. Made in chrome die-cast, originals were plastic. The tilt column switch uses a deeper stem. Replaces Ford Part #: C7OZ-17513-A
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 15-0404 -
1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used Transition cover for the 67 Cougar or Mustang tilt steering column. This flange is different from 68 - 69. The 1967 flange does not have an inner tube to bolt to. ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26748 -
Reproduction course threaded eye bolt for the leaf springs on the 1967 Mercury Cougar or Ford Mustang.Sold individually
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 33091 -
2 piece fuel line. Kit is for fuel and brake lines under the car. Comes as shown. Quality AMK kit. Fits 1967 Mercury Cougar and Ford Mustang. F-3962
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 31982 -
AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 25715 -
Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms.There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to be...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10735 -
Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 18735 -
Good used grade A horn bar with nice, almost perfect chrome. Will have all three vinyl pads / inserts in place but we cannot guarantee we will have your desired color.Replaces Ford part number C7WA-3D755-A. Check out the very first Cougar in our video below!
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 24088 -
Good used grade B horn bar with minimal pitting similar to what is shown in our pictures. Good for a driver quality classic or send it in for re-chrome for your show car. Will have all three vinyl pads / inserts in place but we cannot guarantee we will have your desired color. Please mention in the comments section what color you desire. Ford part number C7WA-3D755-A. Check out the very first Cougar in our video below! ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 12229 -
This restored part will require that you glue your colored vinyl strips in place. If you send in a core, only cores with light pitting can be used to create a show quality finish product.Casting number as seen on back: C7WA-3D755-A. Check out the very first Cougar in our video below! ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 32914 -
Set of three plastic spacers to replace your original brittle cracked parts. These are much stronger than OEM.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19076 -
This listing is for one spring, plastic spacer and screw. Three of these are needed to mount your chrome three spoke horn bezel to your 1967 steering wheel. We also list reproduction 3D printed spacers. Check out the very first Cougar in our video below! ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 30212 -
Very nice reproduction of the steering wheel hub decal with the walking cat to fit the new Shelby steering wheels. Chrome outer rim with plastic black and silver horn button in the center.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 27183 -
Used grade "A" horn center / pad in aqua for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately. Normal 0 false...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27180 -
Used grade "A" horn center / pad in black for the Mercury Cougar. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock, so we'll do what we can to get a good pad for you. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The reproduction center emblem and outer ring can also be purchased separately.*NOTE* Because...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27179 -
Used grade "A" dark blue horn canter / pad for the Mercury Cougar XR7. This will fit and 1967 Cougar, but the dark blue interior color option was XR7 only. This is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can paint it to match your interior. The...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27185 -
Used grade "A" horn center / pad in dark ivy gold / dark green for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the ivy gold interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 27190 -
Used grade "A" horn center / pad in dark red / maroon for the Mercury Cougar XR7. This horn center / pad will fit any 1967 Cougar, but the dark red / maroon interior color was a XR7 option only. his is the best used example of a 1967 horn center / pad. Rarely do we have more than one center as nice as this one in stock but we'll do what we can to get you a good pad. This unit includes a reproduction center emblem and reproduction outer ring, but will be shipped disassembled so that you can...